Copper Talk » Ask The Tech » Antennas » Cb antenna scanner antenna side by side « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Hotwire
Advanced Member
Username: Hotwire

Post Number: 948
Registered: 1-2005
Posted on Sunday, February 19, 2006 - 1:35 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

I have a cobra 148 and a bc350 in the mobile. On the trunk is a silverload and a mobile scanner antenna about 2 feet apart. After removing the scanner to use in the house the cb in the car went CRAZY! SWR went through the roof, audio was terrible and lots of sqeal and worse with amp on I got the worst RF bite I ever had! A lightbulb went off in my head to remove the scanner antenna and feedline. Problem gone. My question is What the heck happened? When I had the scanner hooked up it never caused trouble! How do I prevent this if I wanna put back the antenna? 73 Wire
Top of pagePrevious messageNext messageBottom of page Link to this message

Goat373
Intermediate Member
Username: Goat373

Post Number: 180
Registered: 3-2005


Posted on Sunday, February 19, 2006 - 3:47 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

build or buy a shielded termenation cap to screw the unused scanner coax into....what happend was RF was being picked up at the scanner antennaand ridding the feedline to the un-termenadted end and going "feild-day" in your cab....thus the RF bite, as for the swr, im assuming the RF in the cab also caused this, not as acctually SW, but just the RF playing havoc on your meter
Top of pagePrevious messageNext messageBottom of page Link to this message

Hotwire
Advanced Member
Username: Hotwire

Post Number: 951
Registered: 1-2005
Posted on Sunday, February 19, 2006 - 8:05 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Goat your right about havoc on the meter! I thought it was broke for a minute. I rolled up the feedline and tucked it away in the trunk. When I find something to plug the hole in my trunk lid I can take it out. Any ideals what I can use to plug a 3\8 inch hole?
Top of pagePrevious messageNext messageBottom of page Link to this message

Kmt36264
Junior Member
Username: Kmt36264

Post Number: 10
Registered: 1-2006
Posted on Monday, February 20, 2006 - 12:11 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

If you can't find a rubber plug at an auto parts store, use a bolt, some metal fender washers and some rubber washers.

Another possibility, just get some electrical tape in a similar color and tape it from the inside. Add a small circle of tape over the sticky part of the tape on the outside.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hotwire
Advanced Member
Username: Hotwire

Post Number: 953
Registered: 1-2005
Posted on Monday, February 20, 2006 - 11:15 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

thanks Kmt36264
Top of pagePrevious messageNext messageBottom of page Link to this message

Goat373
Intermediate Member
Username: Goat373

Post Number: 181
Registered: 3-2005


Posted on Tuesday, February 21, 2006 - 7:55 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

wire' firestick makes a rubber grommet for those 3/8/inch hole...they sell them in packs of two i think, my radio shack carries them, good luck on your end though.

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: