Copper Talk » Ask The Tech » Radio's Mobile » Archived Messages » Titan spitfire cherokee dragon am ssb handheld « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Niterider68
New member
Username: Niterider68

Post Number: 8
Registered: 2-2005
Posted on Sunday, October 23, 2005 - 3:13 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

still have not found one can anyone help
thanks pat
Top of pagePrevious messageNext messageBottom of page Link to this message

Bruce
Senior Member
Username: Bruce

Post Number: 3176
Registered: 9-2003
Posted on Monday, October 24, 2005 - 6:48 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

They are rare I have a unmoded one i use on 10 meters ..... got it from copper.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mrsandman
Member
Username: Mrsandman

Post Number: 78
Registered: 1-2002


Posted on Monday, October 24, 2005 - 9:13 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Sidewinder 400:

Peak-Tweak:

<rv5-amc,>

Freq. Expansion:

Remove covers.
Locaste a small PC board on the right side near the front.
There is a set of pins with a jumper over pin 1 and 2.
Remove this jumper and place it on pins 3 and 4.
Replace covers and turn radio on.
Spitfire HandHeld: (Same as Titan RPSY-201):
In the original version, the radio works only in the 10m amateur-band.
Do the following to open it for 454 channels:
From Right toward Left, S1, S2, and S3 will have no Solder Bridges, S4 will have the solder bridge in place and should be left in place.
Remove only the RESISTOR located between S3 and S4 Solder Bridge pads.
Reset the processor by connecting the reset-pad to ground for a second.
After the modification you have to press [Func], [Call] (longer than 3sec.) to enable the full frequency range from 25.160 MHz bis 29.700 MHz (454 channels). This will need to be done any time the radio is turned off, and back on again.
While in this expanded frequncy mode Press [Call] to change bands. You can change from frequency display, to channel display by pressing [Func] and then [Call].
The light can be enabled to stay on by pressing [Func], and then the light button. It will stay on until you turn the radio off or repeat the step to turn it off.
Keybeep is also disabled by holding down the talk button and turning the radio on.
Frequency endings can be changed from 2X.XX0 MHz up to 2X.XX9 MHz modes
this should work but check with 808 for cross ref first!!!!!!!!!!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Niterider68
New member
Username: Niterider68

Post Number: 9
Registered: 2-2005
Posted on Tuesday, November 08, 2005 - 7:02 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

still looking still need help to find an eagle spitfire
Top of pagePrevious messageNext messageBottom of page Link to this message

Niterider68
Junior Member
Username: Niterider68

Post Number: 10
Registered: 2-2005
Posted on Sunday, July 09, 2006 - 8:38 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

finaly found one and it is a rare jem
i got my hands on a magnum ssb-1010 , these were never put into production and only a few dealer demos were sent out the one i received is new.
if anyone has any info on the magnum ssb-1010
am/fm/ssb handheld i would like to hear from you
regards pat

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: