Author |
Message |
Dst
New member Username: Dst
Post Number: 1 Registered: 6-2005
| Posted on Wednesday, June 15, 2005 - 8:19 pm: |
|
I have a Magnum 257 (orange display) and the radio works great on ssb, however AM is weak at best. With amc turned to the maximum, I have to whistle as loud as loud as I can to get any modulation. Where is the amc limiter in this radio??????????????????????????????????????? I know the problems associated with removing the limiter.. |
Jon666
Intermediate Member Username: Jon666
Post Number: 350 Registered: 11-2003
| Posted on Friday, June 17, 2005 - 7:26 pm: |
|
i dont know where it is i have the one with the blue display mine has the same problem it kicks butt on sideband but am stinks mabey a tech could answer that i turned the modulation up inside the radio but it still dont have much modulation |
Tech808
Moderator Username: Tech808
Post Number: 6108 Registered: 8-2002
| Posted on Friday, June 17, 2005 - 8:10 pm: |
|
Dst, Magnum 257 - Models before 11/2004 TUNE – UP / POWER TWEAKS Remove bottom cover Locate RV16. (AM Power) Adjust RV16 for a carrier of 10 watts on AM mode with the RF Power knob turned fully clockwise. With the RF Power knob turned fully counter-clockwise, the AM carrier should be 1 watt. Locate RV4. (Modulation) Adjust RV4 for maximum modulation. Locate RV9. (SSB Power) Adjust RV9 for maximum forward power in SSB mode. Locate RV8. (RF Meter) With RF Output power knob adjusted to show a 5 watt carrier, adjust RV8 just until the 3rd RF power bar lights up. Hope this help's, Lon Tech808 CEF808 N9OSN
|
Tech808
Moderator Username: Tech808
Post Number: 6109 Registered: 8-2002
| Posted on Friday, June 17, 2005 - 8:23 pm: |
|
Jon666, Sorry, I cannot help on this one as I have only worked on only 6 of them and our own and all of them have had 100% modulation on AM. Have you called Sam Lewis at Magnum International at: 1-877-624-6869 and asked him about it? Lon Tech808 CEF808 N9OSN |
Jon666
Intermediate Member Username: Jon666
Post Number: 351 Registered: 11-2003
| Posted on Saturday, June 18, 2005 - 5:56 pm: |
|
yes i sent it to his tech i guess i need a real good powermic for it thanks jon |
747
Intermediate Member Username: 747
Post Number: 108 Registered: 8-2002
| Posted on Wednesday, June 22, 2005 - 5:29 pm: |
|
Jon, The stock mic that comes with the 257/357 series is actually a power mic! There is an adjustment inside the mic to turn the power up/down.. I have seen it - but personally never adjusted it. Has it always been weak, or just now started? |
Wildchild
Junior Member Username: Wildchild
Post Number: 17 Registered: 9-2003
| Posted on Thursday, June 23, 2005 - 5:24 pm: |
|
I think I goofed. I was going to set the RF Meter but I turned RV1 not RV8 (Curse This Old Fading Eyesight Of Mine). Did I do something bad of do I need to have it realigned? Mine is the older model but it has the factory update in it installed when I sent it back for a warranty repair. Please can someone tell me what I have done to it? |
Jon666
Intermediate Member Username: Jon666
Post Number: 353 Registered: 11-2003
| Posted on Thursday, June 23, 2005 - 6:27 pm: |
|
the mic is already at max its a ok radio not great but ok |
Jon666
Intermediate Member Username: Jon666
Post Number: 354 Registered: 11-2003
| Posted on Thursday, June 23, 2005 - 6:29 pm: |
|
its new |
Tech808
Moderator Username: Tech808
Post Number: 6164 Registered: 8-2002
| Posted on Thursday, June 23, 2005 - 6:41 pm: |
|
Wildchild, RV-1 is used to adjust your RX Alignment. If you can remember where it was set at before you moved it try and put it back as close as you can. If you still have good Receive you may be OK if not you may have to have it re-aligned. RV1 is used along with RV402 and you will need a Scope and a Signal generator to get it back to where it is Dead On. If you know of someone who can do it and has the equipment they will need to follow the information below. Adjust RV1 (100KB) for "9" S-RF at EMF 46db in AM E Band Channel 20 and Adjust RV402 (50K) so that you can just see RX wave form EMF 66db and squelch volume maximum. Hope this help's, Lon Tech808 CEF808 N9OSN |
Dst
New member Username: Dst
Post Number: 2 Registered: 6-2005
| Posted on Thursday, June 23, 2005 - 8:32 pm: |
|
Limiter location??????????????? |
Jon666
Intermediate Member Username: Jon666
Post Number: 356 Registered: 11-2003
| Posted on Friday, June 24, 2005 - 5:53 pm: |
|
dont know? |
Mrbigshot
Member Username: Mrbigshot
Post Number: 63 Registered: 2-2005
| Posted on Saturday, June 25, 2005 - 11:59 am: |
|
dont cut limiters!!!!!!!!! EVER!!!!! |