Copper Talk » Ask The Tech » Radio's Mobile » Archived Messages » 95T conversion...Help! I need somebody... « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikefromms
Advanced Member
Username: Mikefromms

Post Number: 593
Registered: 6-2003
Posted on Saturday, April 30, 2005 - 12:14 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

So, I've gotten into the upper escalon of radios here...I'm so impatient...anybody?

Mikefromms
Top of pagePrevious messageNext messageBottom of page Link to this message

Dx431
Senior Member
Username: Dx431

Post Number: 1024
Registered: 2-2002


Posted on Saturday, April 30, 2005 - 12:58 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Mikefromms, try this:

10 METER FM CONVERISON:
(26.065 - 29.655 MHz )

1. Remove the covers from the radio and locate X3 (grid location E3 Main PCB). Replace X3 13.560MHz crystal to a 14.460MHz crystal.
2. Do a complete Alignment of the radio.
3. Re-Assemble the unit and check All Bands and functions for Proper operation.



This will give you the following freqs. in order.


Band A = 26.065 - 26.505
Band B = 26.515 - 26.955
Band C = 26.965 - 27.405
Band D = 27.415 - 27.855
Band E = 27.865 - 28.305
Band F = 28.315 - 28.755
Band G = 28.765 - 29.205
Band H = 29.215 - 29.655

This will allow coverage from:
28.000 - 29.700 and retain the CB / 11 Meter Band.

This mod is in the Modification List on the left of the forum.









Top of pagePrevious messageNext messageBottom of page Link to this message

Mikefromms
Advanced Member
Username: Mikefromms

Post Number: 596
Registered: 6-2003
Posted on Saturday, April 30, 2005 - 1:36 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Thanks for responding. But I don't want to do a complete realignment. What will happen if I don't do that?

Mikefromms
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikefromms
Advanced Member
Username: Mikefromms

Post Number: 597
Registered: 6-2003
Posted on Saturday, April 30, 2005 - 6:54 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Can't locate the x3 gird. I looked and looked on both sides of the board.

Mikefromms
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikefromms
Advanced Member
Username: Mikefromms

Post Number: 598
Registered: 6-2003
Posted on Sunday, May 01, 2005 - 7:21 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

What it showed me was to move (unsolder-not included in what to do instructions) a wire and move it one place up (resolder). I did see the moving a jumper pad on the 48T. Remember, I have the 95T.

Thanks,

Mikefromms
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikefromms
Advanced Member
Username: Mikefromms

Post Number: 599
Registered: 6-2003
Posted on Sunday, May 01, 2005 - 7:40 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

All I've done is move a wire. I get cb only on all bands. Works great. I've looked at the fm conversion but can't find the x3 grid. Just some direction.

Thx.

mikefromms
Top of pagePrevious messageNext messageBottom of page Link to this message

Exman
New member
Username: Exman

Post Number: 3
Registered: 5-2005
Posted on Sunday, June 12, 2005 - 12:54 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

mike, I also have a 95t, if you have the EPT690010C board then x3 is the crystal located on the parts side just behind the knobs about 1" and just left of center, it has a small wire soldered to the top and to L20, L20 is left of a blank spot marked L17. X3 is marked on the board at the top right corner. If you look at the second crystal to the left of the echo board thats it. hope this helps. and good luck.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bobkat
New member
Username: Bobkat

Post Number: 1
Registered: 6-2005
Posted on Sunday, June 12, 2005 - 5:38 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Are these two diff mod's?
Is it one or the other?

I had mine converted from where I purchased it from and don't get near the channels as the FM mod states.

Would I have to put the jumper in it's original location befor the FM mod? and where might I find that value crystal?.

-Thanks

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: