| Author |
Message |
    
Rich
| | Posted on Wednesday, September 19, 2001 - 11:44 am: | 
|
Hi, Does anyone know how to unlock the clarifier on the Galaxy Melaka..? Also How to turn up the modulation? and how much to turn? . Also how to put a 10kc switch in to get the alpha channels..?
How to turn up Am power And ssb Power..? Thankyou Novice here all and any help is much apprecieted Thankyou Rich 73's |
taz
| | Posted on Saturday, October 27, 2001 - 12:23 am: |
|
I would like to know this too, hey 307 can u help us?
taz |
Tech181
| | Posted on Saturday, October 27, 2001 - 11:53 pm: |
|
MOD - VR14
AM Power - VR13
SSB - VR12
Steve
Tech181
Tech181@copperelectronics.com |
Taz
| | Posted on Sunday, October 28, 2001 - 12:18 am: |
|
Thankyou very much!!!!!!!!
Taz |
Sintronic_Cpu
| | Posted on Saturday, March 02, 2002 - 12:36 pm: |
|
To unlock the Clarifier, check your board, make sure it reads EPT360014B, if it does then
1. Remove R141
2. Remove D38
3. Solder bridge J106 pin 54 to 8 volts
http://home.earthlink.net/~galaxytech/LinkedFiles/clarifiermod.jpg
you might need to do some retuning on your frequency just a bit to put it back on center too.
if you need more info, email me at atgrazi@hotmail.com
'73s |
307
| | Posted on Saturday, March 02, 2002 - 10:04 pm: |
|
The whole 9 yards , slider/10Kc/Tune-Up and everything you ever wanted to know about the Melaka is in the Subscibe area of this Forum in step-by-step pictorial descriptions... |
Jyd
| | Posted on Sunday, March 03, 2002 - 10:53 am: |
|
that clarifier mod is for galaxy 77,88,99 not for melaka. |
Sintronic_Cpu
| | Posted on Sunday, March 03, 2002 - 5:45 pm: |
|
I have a Melaka and it's the same EPT . . . check your board for the number EPT360014B, then look up the EPT for the 77,88,99... or the 33 for that matter which that is what the Melaka is, besides...I talked directly to Galaxy and that's what they told me to do, gave me that same link, call them if you do not believe me or check with 307!!! DUH |
Stormy_monday
New member
Username: Stormy_monday
Post Number: 1
Registered: 9-2014
| | Posted on Monday, March 30, 2015 - 7:51 am: |
|
where do i find the step by step mods for galuxy melaka? |
Dale
Senior Member
Username: Dale
Post Number: 2200
Registered: 12-2002
| | Posted on Tuesday, March 31, 2015 - 4:44 pm: |
|
google cbtricks.com
dale/a.k.a.hotrod
cef426
cvc#64
454 [dx numbers]
38lsb
|
Milkman21218
Advanced Member
Username: Milkman21218
Post Number: 624
Registered: 1-2004
| | Posted on Wednesday, April 01, 2015 - 1:21 am: |
|
For the freq mod open up the radio. On the bottom side of tha main board near the front, there is a jumper wire soldered to the board. One end is soldered to board ground and the other end is soldered across two pins. Remove this wire and remove the short between the two pins.
VR14 is Modulation
VR13 is AM Power
VR12 is SSB Power
Izzy
CEF#502
|
