Copper Talk » Ask The Tech » Radio's Mobile » Archived Messages » 29 LTD Antenna Light « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

692
Posted on Saturday, July 13, 2002 - 8:08 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

When i turn the power up on the 29 the antenna
light comes on. Checked SWR on separate meter
and it shows 1.3 (Wilson1000) Whats up with this!

Thanks,692
Top of pagePrevious messageNext messageBottom of page Link to this message

Tech671
Posted on Saturday, July 13, 2002 - 11:59 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

There's an adjustment in the radio that will set the sensitivity on that light.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jyd
Posted on Sunday, July 14, 2002 - 5:19 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

it is a little varible resister in the back of the radio by the coax conector,turn it till it goes off
Top of pagePrevious messageNext messageBottom of page Link to this message

692
Posted on Sunday, July 14, 2002 - 12:03 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Thanks for the reply 671.
Any idea where that is located.
692.
Top of pagePrevious messageNext messageBottom of page Link to this message

307
Posted on Sunday, July 14, 2002 - 8:00 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Right rear side of the main board.

307
Top of pagePrevious messageNext messageBottom of page Link to this message

Ss8541
Posted on Monday, July 15, 2002 - 12:11 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

"what is up with this",.... well, the awi is tuned at the factory to the carrier power of the radio. it works exactly like you swr calibration knob on outside of the radio. the difference here is that it is set to the carrier power of the radio at the factory. when you raise this carrier power, you throw this out of whack. to set the awi back to factory standards, use a non-inductive 150ohm dummyload, key radio and adjust vr6(i think, i'm going by memory) until awi light just lights. now if it comes on, you know you have an swr over 3:1.

but if you just do not want to see it come on, adjust until it stops lighting up. it really isn't important since the 29ltd has a built in swr meter.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jyd
Posted on Monday, July 15, 2002 - 4:56 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

i have not seen a swr meter on a 29 work right anyway
Top of pagePrevious messageNext messageBottom of page Link to this message

Znut
Posted on Monday, July 15, 2002 - 9:30 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

150 ohms?
Top of pagePrevious messageNext messageBottom of page Link to this message

Ss8541
Posted on Monday, July 15, 2002 - 11:56 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

yes 150ohms. this is a 3:1 swr (150/50=3). this is what the awi is set for at the factory. you could use a 100ohm load and then it would be set to come on at a 2:1 swr or higher. but it will also be much more likely to come on when mod is added(especially if mod is wideopen) even if antenna is fine.
Top of pagePrevious messageNext messageBottom of page Link to this message

692
Posted on Saturday, July 20, 2002 - 10:05 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Sorry for the late reply, Had to go make a Buck
with the Truck. Turned VR6 and it still didnt
help Then i unhooked the meter and took care of
the problem. Retuned VR6 and everthing is fine.
Guess it is time to put the old Blackcat back in
the closet.
Thanks again for everyones help. 692

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: