Copper Talk » Ask The Tech » Antennas » Another IMax2000/GPK/Ground question « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Kufbass
New member
Username: Kufbass

Post Number: 2
Registered: 3-2009
Posted on Wednesday, March 11, 2009 - 5:02 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Ok just recieved my Imax2000 w/gpk from ups. Not installing for a few days. Put some clear coat on it. Now the question,because there is so many opinions to this. Going to be mounted on a chimney mount. Base of Imax is going to be 23' from my ground rod. Will this cause rfi. Now not sure if the gpk will stop rfi caused from the ground cable being 23'. Please help. Confused as to puting the ground cable on or not. I am going to be using a RCI-2995 radio so going to put out alot of watts!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Kufbass
New member
Username: Kufbass

Post Number: 3
Registered: 3-2009
Posted on Wednesday, March 11, 2009 - 7:13 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Plus what is the easiest way to bend the gpk to 30 degrees. See it is recommended,but just can't get it bent right.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tech808
Moderator
Username: Tech808

Post Number: 16666
Registered: 8-2002


Posted on Wednesday, March 11, 2009 - 7:30 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Kufbass,

The easiest way I have personally found to bend the 4 corners of the GPK kit/bracket is to place each corner of the bracket in a bench vise and bend to 30°

Hope this help's,
Lon ~ Tech808
N9CEF ~ EN50mk


Top of pagePrevious messageNext messageBottom of page Link to this message

Kufbass
New member
Username: Kufbass

Post Number: 4
Registered: 3-2009
Posted on Wednesday, March 11, 2009 - 10:23 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Ok thx on that. I am just having a hard time with a protractor to messure this out. The way the angle is on the corners. Plz give me a hint to messure. Plus wondering still about the ground wire. Thank you for your help.
Top of pagePrevious messageNext messageBottom of page Link to this message

Streaky
Intermediate Member
Username: Streaky

Post Number: 268
Registered: 3-2006
Posted on Wednesday, March 11, 2009 - 11:04 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

When I had the Imax with the radial kit I had no problems with the ground radiating at all but my feed was at 56 feet but the ground went right from the bracket on the imax right to the ground rod no breaks in the ground wire

Hope this helps you out!!
Streaky
CEF#805
CVC#98
WorldRadio805
The Craziest Station in the Canadian Nation
Top of pagePrevious messageNext messageBottom of page Link to this message

Kufbass
New member
Username: Kufbass

Post Number: 5
Registered: 3-2009
Posted on Thursday, March 12, 2009 - 8:16 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Thinking of doing this. I am replacing my RG-8 coax with LMR-400. I might use the RG-8 as the ground wire. Think this might help a little better then using #10 cable to prevent rvi-tvi. I am thinking this because the RG-8 has ground shielding in the cable. Would this work?? Plus think the cable inside RG-8 is thicker then #10 cable.
Top of pagePrevious messageNext messageBottom of page Link to this message

Dale
Senior Member
Username: Dale

Post Number: 1436
Registered: 12-2002
Posted on Thursday, March 12, 2009 - 4:39 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

well cant comment on the gpk.however i must
say that a chimmney mount is risky .theres
a local here that had his imax on a chinney
mount,and the last severe wind storm we had
not only took down his antenna but also took
down his chimmeney and damaged his roof.id opt
for a tri pod on the roof.
dale/a.k.a.hotrod
cef426
cvc#64
Top of pagePrevious messageNext messageBottom of page Link to this message

Kufbass
New member
Username: Kufbass

Post Number: 6
Registered: 3-2009
Posted on Thursday, March 12, 2009 - 8:24 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Just put up the Imax. Darn was scary at times with the balance of a Imax and a 10'pole. Holding it high enough to get the chimney mount. So you might be right Dale of the chimney mount damage. It is a old house and did have a shakesbeare big stick up there before. Now I hooked up the ground wire to the base of the antenna. Should I move it and put it to the bottom of the 10'pole,or would it not make a diference. Got my dream system going now. RCI-2995,lmr-400,and Imax2000!!!

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: