| Author |
Message |
    
Biskybabyusa
Member
Username: Biskybabyusa
Post Number: 80
Registered: 11-2006
| | Posted on Wednesday, February 11, 2009 - 9:02 pm: | 
|
Any chance of wiring up my hand held Astatic 104 M6B to my Kenwood TS430-S ? Thanks, Jim |
Tech808
Moderator
Username: Tech808
Post Number: 16570
Registered: 8-2002
| | Posted on Thursday, February 12, 2009 - 12:55 am: |
|
KENWOOD-TS120-130-140-180-430-440-450-530-570-680-690-830-870-940-950 Factory wiring.
PIN1 SPEAKER OUT
PIN2 RELAY COMMON GROUND/EARTH
PIN3 PTT FOR FOOT SWITCH
PIN4 RELAY CLOSED ON TRANSMIT
PIN5 RELAY OPEN ON TRANSMIT
PIN6 ALC INPUT
PIN7 +12VOLTS ON TRANSMIT ( 10 Ma Max )
PLUG SHELL EARTH.
============
Astatic 104M6B
TX - Red
MOD - White
REC - Black
SHIELD - Braid/Shield
COMMON - Blue
NOTE!
I have never tried it but that is what the book shows.
Hope this help's,
Lon
CEF#808~HAM#001/N9CEF
CVC#002
Tech808@copperelectronics.com
|
Biskybabyusa
Member
Username: Biskybabyusa
Post Number: 81
Registered: 11-2006
| | Posted on Thursday, February 12, 2009 - 8:40 am: |
|
Hmmm... No idea where to start there ! Can't translate those pinout descriptions, sorry. How about a JDC-201M to the Kenwood TS430-S ? thanks Jim |
Tech808
Moderator
Username: Tech808
Post Number: 16571
Registered: 8-2002
| | Posted on Thursday, February 12, 2009 - 9:13 am: |
|
JCD-201M Microphone Wiring
Pin#1 (E) Shield – Ground
Pin#2 (M) Brown – Mic audio
Pin#3 (P) White – Ground
Pin#4 (G) Green – PTT +
Pin#5 (U) Black – UP
Pin#6 (D) Yellow – DOWN
Pin#7 (C) Blue – UP/DOWN Ground
Pin#8 (B) Red – 5-9 VDC power +
CLICK HERE >JCD-201M
KENWOOD-TS120-130-140-180-430-440-450-530-570-680-690-830-870-940-950 Factory wiring.
PIN1 SPEAKER OUT
PIN2 RELAY COMMON GROUND/EARTH
PIN3 PTT FOR FOOT SWITCH
PIN4 RELAY CLOSED ON TRANSMIT
PIN5 RELAY OPEN ON TRANSMIT
PIN6 ALC INPUT
PIN7 +12VOLTS ON TRANSMIT ( 10 Ma Max )
PLUG SHELL EARTH.
Lon
CEF#808~HAM#001/N9CEF
CVC#002
Tech808@copperelectronics.com
|
Biskybabyusa
Member
Username: Biskybabyusa
Post Number: 82
Registered: 11-2006
| | Posted on Thursday, February 12, 2009 - 8:30 pm: |
|
Thanks, Lon |
Biskybabyusa
Member
Username: Biskybabyusa
Post Number: 83
Registered: 11-2006
| | Posted on Sunday, February 15, 2009 - 6:05 pm: |
|
Got it figured out. Pin 1 white audio, pin 2 red TX, pin 8 shield and blue ! |
Drfeelgood
Junior Member
Username: Drfeelgood
Post Number: 43
Registered: 3-2003
| | Posted on Tuesday, February 17, 2009 - 12:09 am: |
|
hey biskeybabyusa
would you be kind enough to open up your d104 m6b and tell me the wiring for the mic cord on the inside of the mic. ya just remove the back like your replacing the battery and there on the right side of the battery on the pins i got a m6b and the cord was already gone and i have a cord but dont know what wires go where.this be a big help if ya dont care ive tryed to get anyone to help on every board i know of its like noone has one of these mics. if not i'll just go buy a new one and open it up so i can fix this one thanks. |
