| Author |
Message |
    
Johhn
Member
Username: Johhn
Post Number: 66
Registered: 8-2007
| | Posted on Monday, October 08, 2007 - 8:32 pm: | 
|
So the Mod's box shows D59 to cut,
Angelfire,com shows D63,& black wire
at J28 cut and connect to point marked 8v.
at J29..? johhn Help.. |
Tech808
Moderator
Username: Tech808
Post Number: 14505
Registered: 8-2002
| | Posted on Monday, October 08, 2007 - 9:07 pm: |
|
Johhn,
The Clarifier Modification listed in the Modification List located to the left of the forum here is:
UNLOCKING THE CLARIFIER:
#1 ~ Locate the wire harness that runs from the clarifier pot to the circuit board. Located in front of where it plugs into the board, you will see R-197.
#2 ~ Clip the top leg of R-197
#3 ~Use a 6" piece of wire and solder it to the stub of wire sticking out of the board.
#4 ~ Connect the other end of the wire to Pin 3 of IC6.
#5 ~ Locate D-59 a 1N4148 diode. Cut the wire part of this diode to disable it.
#6 ~ Locate R-49 a 100k resistor and change it to a 33k resistor.
Lon ~ Tech808 ~ N9CEF
CEF#808 ~ CEF HAM#33 ~ CVC#002
Tech808@copperelectronics.com
|
Johhn
Member
Username: Johhn
Post Number: 67
Registered: 8-2007
| | Posted on Tuesday, October 09, 2007 - 8:04 am: |
|
Lon Tech808 I read your mods list located to the
Left.Is this for a old or new 2950DX from Copper today? Johhn
Mine is a (new)RCI-2950-DX.. |
Johhn
Member
Username: Johhn
Post Number: 71
Registered: 8-2007
| | Posted on Friday, October 12, 2007 - 7:19 pm: |
|
No reply yet, Lon 808 is this the old or NEW,
2950-DX ? From Copper.. |
Tech808
Moderator
Username: Tech808
Post Number: 14518
Registered: 8-2002
| | Posted on Friday, October 12, 2007 - 9:23 pm: |
|
Johhn,
It would be for the older 2950DX Radios as I have not had the chance to see or use one of the new ones as yet.
Lon ~ Tech808 ~ N9CEF
CEF#808 ~ CEF HAM#33 ~ CVC#002
Tech808@copperelectronics.com
|
Johhn
Member
Username: Johhn
Post Number: 72
Registered: 8-2007
| | Posted on Friday, October 12, 2007 - 10:55 pm: |
|
Thank's Lon I get mine here in Texas next week,I'LL try the D-63 ,&VR-changes and let
you know . johhn 361 cef 936 |
Johhn
Member
Username: Johhn
Post Number: 86
Registered: 8-2007
| | Posted on Wednesday, October 24, 2007 - 9:50 pm: |
|
DO NOT CUT the black wire ,It must still make
conection from the clarifier control To the
F-1 J28 plug. So add a wire to F-1 on top of
The old wire this will make (2)wires on F-1-
J-28 the other end gose to 8-V.8-volts at J-29
J-29 is a test only conector (black) in color.
This dose work ,I did mine 10-18-07 johhn. |
